Hello there lads, how do we configure asterisk 2.7 to use x2 fxo cards
for x2 lines ? i got x2 cards installed and only one works and i
configured it according to manual that says::

There is already a trunk called ZAP/g0 edit this
Enter the phone number for you pots line in the Caller ID field
Enter 1 for Maximum channels
Set a dial rule if you want for this trunk
Select an outbound dial prefix to select this trunk when dialing
Set the Zap Identifier to 1 (the default is g0)
This trunk is now configured


all good for one card how do we configure the other ?

cheers

When setting up the second trunk, set the Zap identifier to 2.

Then as root on the Linux box type in:
genzaptelconf
and enter.

type zttools to see the state of you zap trunks

If you're using x100p clone cards you might not get callerID working
on incoming calls....

phpguy wrote:

> Hello there lads, how do we configure asterisk 2.7 to use x2 fxo cards
> for x2 lines ? i got x2 cards installed and only one works and i
> configured it according to manual that says::
>
> There is already a trunk called ZAP/g0 edit this
> Enter the phone number for you pots line in the Caller ID field
> Enter 1 for Maximum channels
> Set a dial rule if you want for this trunk
> Select an outbound dial prefix to select this trunk when dialing
> Set the Zap Identifier to 1 (the default is g0)
> This trunk is now configured
>
>
> all good for one card how do we configure the other ?
>
> cheers

thank you very much for your response

when i want to do outgoing calls which line will be used as default ?
the zap 1 ? if tis busy will the zap 2 be used automatically or not ?

cheers

phpguy explained on 08/01/2008 :
> thank you very much for your response
>
> when i want to do outgoing calls which line will be used as default ?
> the zap 1 ? if tis busy will the zap 2 be used automatically or not ?

Can't you just select the relevant trunks in your outbound routes page.

Choose ZAP/gO as the first in the sequence..... and the other for the 
next in the sequence.

"Jono" <nothanks@blueyonder.invalid> wrote in message 
news:mn.45747d818c4c296f.77298@blueyonder.invalid...
> phpguy explained on 08/01/2008 :
>> thank you very much for your response
>>
>> when i want to do outgoing calls which line will be used as default ?
>> the zap 1 ? if tis busy will the zap 2 be used automatically or not ?
>
> Can't you just select the relevant trunks in your outbound routes page.
>
> Choose ZAP/gO as the first in the sequence..... and the other for the next 
> in the sequence.
>
>
http://www.doorloadingservices.co.uk

It happens that ><)))'> Orange Peel <'(((>< formulated :
> "Jono" <nothanks@blueyonder.invalid> wrote in message 
> news:mn.45747d818c4c296f.77298@blueyonder.invalid...
>> phpguy explained on 08/01/2008 :
>>> thank you very much for your response
>>>
>>> when i want to do outgoing calls which line will be used as default ?
>>> the zap 1 ? if tis busy will the zap 2 be used automatically or not ?
>>
>> Can't you just select the relevant trunks in your outbound routes page.
>>
>> Choose ZAP/gO as the first in the sequence..... and the other for the next 
>> in the sequence.
>>
>>
> http://www.doorloadingservices.co.uk

OK, thanks. Not quite sure of the relevance, though.