Door panels
Wed, 20 Aug 2008 21:01:24 +0100
We have a half-glazed double-glazed back door - just a standard white
plastic door (I could find out who made it if I had to). It has a cat flap
in it, wot I cut myself. If I wanted to replace the lower plastic panel for
one that didn't have a hole cut in it would I be looking at mucho wonga or
are they a stan ...
|
Re: Cost of Papering/Painting One Wall
Wed, 20 Aug 2008 20:46:20 +0100
In message <kvboa4940leavb77iona8hh1nr6r79vvrp@4ax.com>,
NOSPAMnet@gmail.com writes
>I'm in Glasgow..Does that sound reasonable?
Erm - better not answer that
--
geoff ...
|
Re: Cost of Papering/Painting One Wall
Wed, 20 Aug 2008 19:50:41 GMT
On Wed, 20 Aug 2008 20:44:12 +0100, NOSPAMnet wrote:
> On Wed, 20 Aug 2008 19:31:35 GMT, Cicero <sheldrake@hellfire.co.uk>
> wrote:
>
>>On Wed, 20 Aug 2008 16:00:31 +0100, NOSPAMnet wrote:
>>
>>> I know this is DIY but I'm sure some of you will be able to give an
>>> opinion .I have a wall that has been gypr ...
|
Re: Cost of Papering/Painting One Wall
Wed, 20 Aug 2008 19:31:35 GMT
On Wed, 20 Aug 2008 16:00:31 +0100, NOSPAMnet wrote:
> I know this is DIY but I'm sure some of you will be able to give an
> opinion .I have a wall that has been gyproc'd and emulsioned .but the
> finish simply isn't right compared to the other walls and the ceiling
> and when I did it I could not get it to a sa ...
|
Sand Bags
Wed, 20 Aug 2008 19:55:56 +0100
Having just used up a ton of sand, I now have an empty one-trip poly bag.
It seems I have two options. Roll it up and put into dustbin. Or find an
alternative use for it.
Any suggestions? It seems such a waste to chuck it.
--
Rod
Hypothyroidism is a seriously debilitating condition with an insidious
...
|
A Question for Real Electricians ?
Wed, 20 Aug 2008 18:58:03 +0100
Occassionally after removing a 13 A socket form a wall, to replace with a
new one, I have come across the problem that the end of the cable breaks off
just where it was gripped by the screw, usually this happens with the earth
wire.
Sometimes when I go to refit the socket I find that the wire is now too
sho ...
|
B&D wormate ?30
Wed, 20 Aug 2008 16:16:57 GMT
http://www.screwfix.com/prods/63272?ts=48833
...
|
floor slab mix / reinforcement
Wed, 20 Aug 2008 08:58:29 -0700 (PDT)
I'm now ready to pour my floor slab. 5 inch thick slab over 3 inch
kingspan.
I'm getting readymix pumped to the site. What mix should I ask for
(C20, ST4 etc) ?
Also, will I need reinforcment in this (fibres, steel mesh
reinforcement) ?
Thanks,
Simon. ...
|
You dozy git
Wed, 20 Aug 2008 14:31:35 GMT
just bought a pkt of ¡ê4 Araldite Rapid glue,got a stanly knife to cut open
the heat sealed packaging...anyone guess what happened next?
No I never cut myself.
...
|
kilowatts along 10mm/15mm/22mm copper.....
Wed, 20 Aug 2008 14:48:05 +0100
.... at typical combi flow rates?
I've seen this mentioned somewhere but damned if I can find it.
Just trying to get a ball-park figure for rads feedable from each size.
TIA
...
|
