nv relay
Tue, 14 Jul 2009 09:41:55 +0100
Though otherwise in excellent condition my recently acquired Student 1800
has no No Volt relay. All that remains is a black blob that at some point,
after it melted, has been removed from the circuit :-)
Any thoughts on a suitable replacement and a source welcome.
thanks
--
Roland Craven
Nr. Exeter, Devon, ...
|
Chuck guard glazing material?
Mon, 13 Jul 2009 08:30:32 -0700 (PDT)
I want to replace the 'glazing' in a metal-framed chuck guard, as well
as the window covering the gearbox scale on my lathe.
I was thinking in terms of polycarbonate, but I know it scratches
easily and it's also expensive - I have to buy an 8' x 4' sheet for
well over ¡ê100, or pay to have it cut to size. The chuck ...
|
Exhaust silencer repair
Mon, 13 Jul 2009 00:28:32 +0000
Hi folks,
Is there anyone here with the equipment and skills necessary to repair
an exhaust silencer? The 1947 Dennis motor mower that I'm restoring has
an unusual silencer. The outer skin of the silencer is rusted through in
several places, but I cannot find a similar replacement. The closest I
can find is ...
|
Chinese scales
Sun, 12 Jul 2009 04:54:35 -0700 (PDT)
Does anyone have pinouts/colour coding of the nine pin D plug on a
Sino scale?
The model of scale is JCXE-DFH
Mark.
www.ems-fife.co.uk ...
|
Damaging aluminium through heating.
Sun, 12 Jul 2009 12:51:24 +0100
I'm trying to remove 8mm BMS axles from some aluminium parts and so
far the only method which has yielded results is heating the aluminium
parts with a butane torch for ten to fifteen seconds before attempting
to remove the axle.
Is there any risk to the future strength of the aluminium parts by
putting them th ...
|
Modifications to a Myford ML7R
Sat, 11 Jul 2009 20:42:48 +0100
I have a ML7R which is essentially a standard ML7 fitted with a super7
headstock and tailstock introduced by Myford in the late 70s.
I'm becoming ever more frustrated by the limited range of angles that
the topslide can be rotated (+/- 45 degrees). I am considering imitating
the Super 7 design by fitting a do ...
|
Accuracy stuff
Sat, 11 Jul 2009 17:17:44 +0100
I need a MT3 test bar, accurate to a hundredth of a mm, and preferably
to a couple of microns, at say 150 mm.
I also need an MT3-MT2 reducer sleeve, accurate to something better than
the 3 thou plus the horrible one I bought from Chester is - and
preferably, again, accurate to a hundredth-, or a couple of mic ...
|
Disc
Fri, 10 Jul 2009 10:21:00 -0500
Any suggestion what disc i need for my metal works. I'm planning to
build a C130 model RC and though I'd ask ya'll what would be perfect to
use. I actually have something in mind but wanted to ask ya'll if this
can work (http://stores.shop.ebay.com/smith-and-arrow__W0QQ_armrsZ1)
thanks.
--
banvolt
--------------- ...
|
Poly-V 10-Groove L section Pulley
Thu, 09 Jul 2009 20:49:43 +0100
Does anyone know of a UK supplier that would carry the Poly-V pulleys in the 'L'
size of belts (4.70mm groove pitch) ?
I'm looking for a 190mm diameter 10-Groove pulley with 50mm Taper-Lock (which
can be bought separately) That's about 7.5" X 2.25" wide in old money.
I have one on another piece of equipment bu ...
|
Wipers
Thu, 9 Jul 2009 17:19:55 +0100
Colchester want ¡ê75 for a set of wipers for my Student 1800!
Any ideas on a suitable material to make em from please. Obviously I can
live without the gold-plate......
--
Roland Craven
Nr. Exeter, Devon, UK
roland@petternut.co.uk
www.petternut.co.uk
...
|
