Back issue of Model Engineers' Workshop
Sat, 1 Aug 2009 15:48:26 +0930
Hi,
The latest issue of MOW in Australia (Darwin) is number 151 (June 2009).
There is an article in it about making a metal mangle in which mention is
made of a previous article in issue 123 by Gary Wooding which was about
making a jeweller's rolling mill.
I tried to send an email to customer.services@myho ...
|
Parkanson Power Hacksaw
Sat, 01 Aug 2009 13:00:26 +0930
Good day to all ,
Further to a previous post some time ago which some commented on .
I have been recently restoring an old Parkanson power hacksaw that I
rescued from a local scrap yard and have made a video ,which I posted to
youtube here is a link if you are interested in viewing the video .
http://www.yo ...
|
Pinging Norman Atkinson
Fri, 31 Jul 2009 12:09:52 -0700 (PDT)
Anyone heard anything of Norman.Haven`t seen him posting anywhere and
an email to him has gone unanswered.
Not like him not to pop up somewhere. ...
|
Orthoganol balancing - twinwheel grinders
Fri, 31 Jul 2009 15:05:13 +0100
I've recently had to fit a new wheel and rebalance my 8" twin
wheel grinder. The method I use is pretty straightforward but may
be of interest because it doesn't seem to be well known
A good start is to dress both wheels and then remove and
individually statically balance each wheel. This only a partial
cure ...
|
Type metal
Fri, 31 Jul 2009 07:41:44 +0100
Has anyone a small quantity of type metal I can relieve them of for
beer tokens? Either as a lump or as actual type?
I need to cast a slug into the undamaged inner end of a female spline
so that I can make a shaper tool to produce a replacement. (Type metal
contains small amounts of antimony which expands on coo ...
|
Kennet grinder
Thu, 30 Jul 2009 14:43:14 -0500
Does any member know where Ican get a set of drawings for a Kennet T and
C grinder, is their any to download ? thanks David
--
stereotype
------------------------------------------------------------------------
stereotype's Profile: http://www.rcgroups.com/forums/member.php?u=119209
View this thread: http://www.rc ...
|
Search Posts
Thu, 30 Jul 2009 06:49:30 -0700 (PDT)
I know many of you guys don't use Google Groups but I used to find the
search facility handy. Lately it fails to find anything on even a
basic search like "Lathe Tools", anyone have the same problem or have
an alternative to search the archive.
regards
Keith ...
|
Pinging Andrew Mawson
Wed, 29 Jul 2009 12:19:21 +0100
This wasn't you back in the 70s was it?
http://i120.photobucket.com/albums/o191/rd400c/Untitled2.jpg
http://i120.photobucket.com/albums/o191/rd400c/Untitled10-1.jpg
(the name is on the text on the 2nd page) ...
|
3/32" silver steel rod needed
Wed, 29 Jul 2009 10:02:55 +0100
Hi all,
Anyone have a piece lying around - I need to make some valve gear pins.
thanks
Lee ...
|
Source of small piece of 1/4" perspex sheet
28 Jul 2009 22:56:51 +0100 (BST)
Does anyone know of a friendly place which might have offcuts of
1/4 inch thick perspex sheet to sell?
I need a piece from which I can cut a tiny section about 2 1/4 inches
by 3/4 inch so I don't really want to buy a whole sheet (but clearly
I expect to buy a bigger piece than I need!)
It will serve me as ...
|
